Choosing an air compressor: airflow, pressure and tank capacity

Choose an air compressor by matching the air your tools consume with the air the compressor delivers at the required pressure. Horsepower and tank litres help describe the machine, but they do not answer whether two tools can run together.

A useful comparison starts with a small demand sheet: the tools, their air consumption, operating pressure and how long they run. You can then compare the compressor options in Yuri's generator and compressor collection against a stated requirement.

Read the figures as different measurements

Specification What it answers
Delivered airflow How much air the compressor supplies over time under stated conditions
Operating pressure The pressure associated with that delivery rating
Tank capacity How much compressed air the receiver stores
Motor power The motor's power rating
Duty information The running pattern and limits the manufacturer permits

A 50-litre tank and a rating of 200 litres per minute describe different things. The first is a volume; the second is a flow rate. Keep the units with the number whenever you compare quotations.

Use delivered airflow at a stated pressure

A compressor may list an intake or displacement figure as well as a delivered-air rating. These are different measurements. Ask which one is quoted before comparing it with an air tool's consumption.

Free air delivery, or FAD, expresses delivered air as an equivalent volume at stated inlet or reference conditions. That provides a basis for comparing supply with demand, provided the figures use compatible conditions. The compressor's operating pressure must still be stated alongside the delivery rating.

Motor power alone cannot fill in a missing flow figure. Two machines with the same horsepower label may have different delivery specifications and operating limits.

Work through a two-tool example

The figures below are illustrative, not ratings for Yuri tools. Assume both tools run continuously together at 6 bar, and their consumption is expressed on the same free-air basis.

Requirement Air consumption
Tool A at 6 bar 180 litres/minute
Tool B at 6 bar 120 litres/minute
Combined demand 300 litres/minute

A compressor delivering 250 litres per minute at the required pressure cannot keep up with that sustained combined demand. Stored air may cover a short period, but the receiver will not create the missing continuous delivery.

A hypothetical compressor delivering 360 litres per minute at that pressure clears the first flow comparison. The remaining checks include its permitted duty, pressure losses, air treatment, leakage allowance and any planned additional demand. The difference between 360 and 300 is not a universal sizing margin.

If Tool B is used only occasionally, record that operating pattern. Do not replace a peak requirement with an average figure without checking how the receiver and compressor will handle the peak.

Decide what the tank must do

The receiver stores air and helps accommodate changing demand. A brief use of an air tool and a continuous production task create different storage and replenishment requirements.

Atlas Copco's air-receiver guidance explains that useful storage depends on the pressure the application needs and how long that supply must last. Tank volume is therefore part of the setup review, alongside delivery and operating pattern.

A larger tank can change the available storage. It does not automatically increase the compressor's delivered airflow or establish that the motor can run continuously.

Check the system at the tool

The pressure required at the tool is not necessarily the pressure available after air has passed through a hose, regulator, filter and couplings. Include those components when describing the installation.

Record hose length and internal diameter, simultaneous tools, any air-treatment requirements and the available electrical supply. A quotation should identify what is included and what must be purchased separately.

For an impact-wrench requirement, the cordless versus pneumatic impact-wrench guide explains why the air supply belongs in the tool decision. Use the exact pneumatic tool's consumption data for compressor sizing.

Prepare a comparison that suppliers can answer

Send the tool models, documented pressure and consumption figures, and the expected simultaneous running pattern. Ask each supplier to return:

  • Delivered airflow at the relevant operating pressure, with the measurement basis stated.
  • Tank capacity and the documented duty information.
  • Supply requirements and the proposed hose, regulator and treatment arrangement.
  • Supplied accessories and any additional components required.

Keeping those fields consistent makes the quotations easier to compare. Identify the request as an air-compressor requirement when browsing a collection that also contains generators.

Frequently asked questions

Does a larger tank mean I can run more tools continuously?

Not necessarily. Compare sustained air demand with delivered airflow at the required pressure. The receiver can support changing or short-term demand, but continuous demand still needs adequate replenishment.

What if a listing shows only horsepower and tank litres?

Request the delivered-airflow rating, its associated pressure and the permitted running pattern. Those missing figures are needed before the machine can be matched to a particular air tool.

Can I compare two airflow numbers if their measurement conditions differ?

Only after establishing a compatible basis. Keep the flow terminology, reference conditions and operating pressure with each figure rather than comparing the largest numbers in the listings.

Back to blog